Shipping is with tracking number, exactly 80 Czech korun
to Europ and 86 Czech korun to other countries,
You will notice that once you receive the item.
So shipping is normaly more than 4$.
3.99$ is made for all buyers.
==========================================
100% Satisfaction guaranteed!
START STRAIGHT OUT OF THE BOX!
No PIC programmer is required.
The board has Microchip bootloader installed on it!
CHOOSE 1bit OR 32bit USB OTG MICROCONTROLLER :
PIC32MX795F512L
PIC32MX460F512L
dsPIC33EP512MU810
PIC24EP512GU810
PIC24EP256GU810
==========================================
PIC32,PIC24 and dsPIC33
USB OTG Development Board
Overview
The SnadPIC is a microcontroller board based on the Microchip PIC32, PIC24 and dsPIC families. It is designed to be easy to use and suitable for use by anyone from beginners to advanced users for experimenting with electronics and embedded control systems. It contains everything needed to start developing embedded applications.
It is designed to provide a low cost small control solution. It is intended to introduce and
demonstrate the capabilities and features of PIC32, PIC24 and dsPIC33 with on- chip USB OTG. The board also comes with all the basic components needed for the Microchip PIC32, PIC24 and dsPIC33 families, so you can use it straight out of the box. Except for a single connection to a computer, no additional hardware or configuration is necessary. A USB connection to a host computer supplies communications and power to the board. For independent host-side USB operation, the starter kit may be disconnected from the PC and powered through DC Power Jack for independent functionality. The starter kit provides 83 I/O pins that support a number of peripheral functions, such as UART, SPI and I2C™ ports and pulse width modulated outputs. Use of these advanced peripherals requires an add on board to provide the additional hardware required.
Through the USB interface, it can also be programmed without the need of a programmer, as there is a built in Microchip boot loader.
The starter kit can be powered via USB, an external DC power adapter, or batteries.
Picture
Features
• PIC32, PIC24 and dsPIC33 with on-chip USB OTG
• Microchip bootloader Firmware
• USB serial interface easily can be used as USB host and USB device
• On-board Micro USB Connector
• On-board Micro SD Card holder
• On-board External Power Connector
• On-board Power Supply Switch (ON OFF ON)
• On-board 5V regulator
• On-board 3.3V regulator
• On-board Shield Power Connector
• On-board RESET (MCLR) Switch
• On-board General purpose Switch
• On-board LED Power Supply indicator
• On-board 8 User LEDs, and 1x8 male/female pin header that provides connections to these LEDs
• Most of the processor pins available, and the breakout pins can be soldered with standard 0.1″male/female header
to easily plug it into a mother board
• 4 holes to fix the board into a mother board
• On-board 8Mhz Crystal and two capacitors
• On-board 32.768Khz Crystal and two capacitors for RTCC/Timer1
• On-board 1x6 footprint for ICSP connection that provides Microchip Debug Tool Connector
• Board Size Inches (mm) : 3.94 (100.25) x 2.39 (60.95)
Datasheet and more info here : http://snadpic.weebly.com/
Do you need a demo application? Please contact us
==========================
If you don't know where to start,
it is easy by visiting Microchip website..
Here is the link to all what you need :
Once you download the Microchip Libraries for Applications you can select the projects that you
need for your application. In addition to the source code,
this software package includes: schematics, drivers, demos, documentation, and utilities.
==========================
The device (MCU) is new never been programmed before or tested.
It was taken from its original package and soldered - with care - on the board :
home, hand soldering skills.
IT LOOKS LIKE IT WAS SOLDERED IN FACTORY!
Every board is tested with SD Card, LEDs,
and tested as a USB device and USB Host
NO NEED TO ANOTHER PROGRAMMER TO START APPLICATIONS
BUT IF YOU DON'T WANT TO USE THE BOOTLOADER SO:
Warning for PICKIT3 Users
Do not use the "programmer-to-go" button when there is no image on the programmer
Doing so will put a PIC32 microcontroller into an irrecoverable state.
See this Microchip Forum thread for details.
------------------------
